- Individual programmable Quad RS-232, RS-422/485
- Programmable 16 Discrete RS-422 Transceiver with Interrupt support
- Edge selection support: positive and/or Negative
- Global Interrupt Signal Register
- Each UART compatible 16C550 with 64-byte TX and RX FIFOs
- Automatic RTS/CTS Hardware Flow Control
- Automatic RS485 Direction Control Output with Selectable turn-around delay
- Up to 6.125 MBps Data Rate
- Integrated, Logic-Selectable 120Ω Termination Resistor
- No Damage or Latchup to ESD: ±15kV HBM
- High Input Impedance Supports 256 Nodes
PMC-SCC04-IO
Quad Serial Communication Interface with 64-Byte FiFO Programmable RS-232, RS-422/485 16 Discrete RS-422 I/O Lines
- Individual programmable Quad RS-232, RS-422/485
- Programmable 16 Discrete RS-422 Transceiver with Interrupt support
- Edge selection support: positive and/or Negative
- Global Interrupt Signal Register
- Each UART compatible 16C550 with 64-byte TX and RX FIFOs
- Automatic RTS/CTS Hardware Flow Control
- Automatic RS485 Direction Control Output with Selectable turn-around delay
- Up to 6.125 MBps Data Rate
- Integrated, Logic-Selectable 120Ω Termination Resistor
- No Damage or Latchup to ESD: ±15kV HBM
- High Input Impedance Supports 256 Nodes
Share this product
LinkedIn
PMC-SCC04-IO
Quad Serial Communication Interface with 64-Byte FiFO Programmable RS-232, RS-422/485 16 Discrete RS-422 I/O Lines
The PMC-SCC04-IO module is a Quad Channel serial communication controller featuring 64-byte FIFOs per line, based on the XR17D154 chip. It supports auto-configuration registers for plug-and-play installation and provides four asynchronous ports capable of up to 6.125 MBps. Each UART includes a 16C550-compatible set of configuration registers, 64-byte transmit and receive FIFOs with programmable trigger levels and counters, automatic hardware and software flow control, IrDA encoder/decoder, 8 multi-purpose I/Os, and a 16-bit general-purpose timer/counter. The module offers high input impedance with ESD protection and logic-selectable 120-ohm termination resistors for each channel. Additionally, it provides 16 RS-422 I/O lines that are individually programmable as input or output, with software-programmable termination resistors
Applications
- Process Control and Industrial Automation
- Precision Instrumentation
- Direct Digital Waveform Generation
PMC Interface
- PCI Bus Target revision 2.2 Signaling Compliant
- VIO 3.3/5.0 Volts
- 32 Bit, 33 MHz
- Interrupts
- DMA
Operating: Environmental
- Operating temperature
- Commercial: 0 to +70 °C
- Optional: -40°C to +85°C
- Airflow requirement: .5 CFM
- Humidity: 5 to 90% (non-cond.)
- Altitude: 0 to 30,000 ft
Mechanical: Environmental
- Size: Single wide PMC 2.92″ x 5.87″
- Power: 1.5 watt
- Front panel I/O
- Vibration: 0.5G RMS 20-2000 Hz rand
- Shock: 20 G, 11 ms, ½ sine
- Weight: tbd
Ordering Information
- Part Number: PMC-SCC04-IO-XX-RIO – 4 Channel RS-422/485, 16 I/O RS-422 Lines with Rear I/O only
- Part Number: PMC-SCC04-IO-XX-FP – 4 Channel RS-422/485, 16 I/O RS-422 Lines with Front and Rear only
- XX: Desired Oscillator Frequency Option
- Part Number: PMC-SCC04-IO-XX-YY-I – Same as above with -40 to +85°C
Optional Accessories
- Part Number: TB-68-SCSI – 68 pin terminal block and 1 meter flat ribbon cable
- Part Number: CBL-68-SCSI – 68 pin, 1 meter flat ribbon cable, IDC header connector
Data Sheet – Link Here
- Individual programmable Quad RS-232, RS-422/485
- Programmable 16 Discrete RS-422 Transceiver with Interrupt support
- Edge selection support: positive and/or Negative
- Global Interrupt Signal Register
- Each UART compatible 16C550 with 64-byte TX and RX FIFOs
- Automatic RTS/CTS Hardware Flow Control
- Automatic RS485 Direction Control Output with Selectable turn-around delay
- Up to 6.125 MBps Data Rate
- Integrated, Logic-Selectable 120Ω Termination Resistor
- No Damage or Latchup to ESD: ±15kV HBM
- High Input Impedance Supports 256 Nodes
| Mechanical Interface | Switched Mezzanine Card (XMC) Interface confirming to ANSI/VITA 42.0-2008 (Auxiliary Standard) Standard single-width (149mm x 74mm) | |||||||||
| Electrical Interface | PCI Express x4 Link (Base Specification 2.1) compliant interface conforming to ANSI/VITA 42.3-2006 (PCI Express Protocol Layer Standard) | |||||||||
| PCI Express Switch | PI7C9X2G312GP (Pericom) | |||||||||
| PCI Express to PCI Bridge | XIO2001 (Texas Instruments) | |||||||||
| User configurable FPGA | TXMC639-10R: XC7K160T-2FBG676I (AMD) TXMC639-11R: XC7K325T-2FBG676I (AMD) | |||||||||
| SPI-Flash | MT25QL128 (Micron) 128 Mbit (contains TXMC639 FPGA BRD) or compatible; +3.3 V supply voltage | |||||||||
| DDR3 RAM | 2x MT41K256M16TW-107 (Micron) 256Meg x 32 bit | |||||||||
| Board Configuration Controller | LCMXO2-7000HC (Lattice) | |||||||||
| ADC | LTC2320 -16 (Analog Devices) | |||||||||
| DAC | AD5547BRUZ (Analog Devices) | |||||||||
| A/D Channels | TXMC639-10R: 8 Differential 16bit A/D Channels TXMC639-11R: 16 Differential 16bit A/D Channels Input Configuration per BCC Device: Input Voltage Ranges: Differental : ±20.57 V, ±10.28 V or ±5.14 V (Single-Ended: ±10.28 V, ±5.14 V or ±2.57 V) All analog inputs are connected via an impedance converter and a second operation amplifier for level adjustment and filtering to the differential ADC inputs. The -3 dB limit of this input stage is at approx. 8MHz | |||||||||
| D/A Channels | TXMC639-10R: 4 Single-Ended 16 Bit D/A Channels TXMC639-11R: 8 Single-Ended 16 Bit D/A Channels Output range configurable per D/A channel. Maximum single-ended Output Voltage – Vout: ±10 V Maximum Output Drive Current for each Output: 10 mA Maximum Capacitive Load for each Output: 1000 pF Typical Settling Time for a 10 mA / 1000 pF: < 1 µs | |||||||||
| Digital Front I/O Channels | 32 digital I/O Lines
| |||||||||
| Digital Rear I/O Channels | 64 direct FPGA I/O lines to P14 Rear I/O connector
4 MGT line to P16 Rear I/O connector
| |||||||||
| Front I/O | Front I/O Samtec – ERF8_050_01_L_D_RA_L_TR | |||||||||
| P14 Rear I/O | 64 pin Mezzanine Connector (Molex 71436-2864 or compatible) | |||||||||
| P16 Rear I/O | 114 pin Mezzanine Connector (Samtec – ASP-105885-01) | |||||||||
| Power Requirements 1) | Depends on FPGA design With TXMC639 Board Reference Design / without external load
| |||||||||
| Temperature Range | Operating: – 40 °C to + 85 °C Storage: – 55 °C to + 125 °C | |||||||||
| MTBF 1) | 157 000 h to 161 000 h | |||||||||
| Humidity | 5% – 95% non-condensing | |||||||||
| Weight | 140 g |
1) depends on variant, for further details see User Manual
TXMC639-10R
| 8x Analog In, 4x Analog Out, XC7K160T-2FBG676 Kintex™ 7 FPGA AMD Kintex™ 7 FPGA (XC7K160T-2FBG676), 1GB DDR3, 8x Analog In, 4x Analog Out, 32x digital Front I/O, 64x direct FPGA Rear I/O Lines and 4x MGTs Rear I/O |
TXMC639-11R
| 16x Analog In, 8x Analog Out, XC7K325T-2FBG676 Kintex™ 7 FPGA AMD Kintex™ 7 FPGA (XC7K325T-2FBG676), 1GB DDR3, 16x Analog In, 8x Analog Out, 32x digital Front I/O, 64x direct FPGA Rear I/O Lines and 4x MGTs Rear I/O |
SOFTWARE
Share this product
LinkedIn
