- 6 Standalone CAN Controller
- Support CAN 2.0B protocol
- Support 11/29-bit identifier
- Bit rates up to 1 Mbits/s
- ISO11898 Compatible
- Support PeliCAN mode extensions
- No external power required for isolation
- Selectable 120Ω Termination
- 5000Vrms Isolation
- PMC-CAN6
- Operating: Environmental
- Operating temperature:
- Commercial: 0 to +70 °C
- Optional: -40°C to +85°C
PMC-CAN6
SIX CHANNELS CAN BUS
- 6 Standalone CAN Controller
- Support CAN 2.0B protocol
- Support 11/29-bit identifier
- Bit rates up to 1 Mbits/s
- ISO11898 Compatible
- Support PeliCAN mode extensions
- No external power required for isolation
- Selectable 120Ω Termination
- 5000Vrms Isolation
- PMC-CAN6
- Operating: Environmental
- Operating temperature:
- Commercial: 0 to +70 °C
- Optional: -40°C to +85°C
Share this product
LinkedIn
PMC-CAN6
SIX CHANNELS CAN BUS
The PMC-CAN6 module features six channels of CAN bus interface utilizing NXP SJA1000 CAN controllers, with each channel’s transceiver individually isolated up to 5000Vrms. Supporting the CAN 2.0B protocol, the device accommodates both 11-bit and 29-bit identifiers and includes PeliCAN Mode extensions. Compliant with ISO11898 standards, the board offers transfer bit rates up to 1 Mbit/s and provides each channel with a logic-selectable 120 Ohm termination resistor.
PMC interface
- PCI Bus Target revision 2.3 Signaling Compliant
- VIO 3.3/5.0 Volts
- 32 Bit, 33 MHz
- Interrupts
- Airflow requirement: .5 CFM
- Humidity: 5 to 90% (non-cond.)
- Altitude: 0 to 10’000 ft
Mechanical: Environmental
- Size: Single wide PMC 2.92″ x 5.87″
- Power: 1.5 watt
- Front panel I/O
- Vibration: 0.5G RMS 20-2000 Hz rand
- Shock: 20 G, 11 ms, ½ sine
- Weight: tbd
- MTBF: >250000 hours
ORDERING INFORMATION
- Part Number: PMC-CAN6 – 6 Channel CAN bus Controller
- Part Number: PMC-CAN6-I – Same as above with -40 to +85°C
Optional Accessories
- Part Number: TB-50-SCSI – 50 pin terminal block and 1 meter cable
- Part Number: CBL-50-SCSI – 50 pin, 1 meter cable
Data Sheet – Link Here
- 6 Standalone CAN Controller
- Support CAN 2.0B protocol
- Support 11/29-bit identifier
- Bit rates up to 1 Mbits/s
- ISO11898 Compatible
- Support PeliCAN mode extensions
- No external power required for isolation
- Selectable 120Ω Termination
- 5000Vrms Isolation
- PMC-CAN6
- Operating: Environmental
- Operating temperature:
- Commercial: 0 to +70 °C
- Optional: -40°C to +85°C
| Mechanical Interface | Switched Mezzanine Card (XMC) Interface confirming to ANSI/VITA 42.0-2008 (Auxiliary Standard) Standard single-width (149mm x 74mm) | |||||||||
| Electrical Interface | PCI Express x4 Link (Base Specification 2.1) compliant interface conforming to ANSI/VITA 42.3-2006 (PCI Express Protocol Layer Standard) | |||||||||
| PCI Express Switch | PI7C9X2G312GP (Pericom) | |||||||||
| PCI Express to PCI Bridge | XIO2001 (Texas Instruments) | |||||||||
| User configurable FPGA | TXMC639-10R: XC7K160T-2FBG676I (AMD) TXMC639-11R: XC7K325T-2FBG676I (AMD) | |||||||||
| SPI-Flash | MT25QL128 (Micron) 128 Mbit (contains TXMC639 FPGA BRD) or compatible; +3.3 V supply voltage | |||||||||
| DDR3 RAM | 2x MT41K256M16TW-107 (Micron) 256Meg x 32 bit | |||||||||
| Board Configuration Controller | LCMXO2-7000HC (Lattice) | |||||||||
| ADC | LTC2320 -16 (Analog Devices) | |||||||||
| DAC | AD5547BRUZ (Analog Devices) | |||||||||
| A/D Channels | TXMC639-10R: 8 Differential 16bit A/D Channels TXMC639-11R: 16 Differential 16bit A/D Channels Input Configuration per BCC Device: Input Voltage Ranges: Differental : ±20.57 V, ±10.28 V or ±5.14 V (Single-Ended: ±10.28 V, ±5.14 V or ±2.57 V) All analog inputs are connected via an impedance converter and a second operation amplifier for level adjustment and filtering to the differential ADC inputs. The -3 dB limit of this input stage is at approx. 8MHz | |||||||||
| D/A Channels | TXMC639-10R: 4 Single-Ended 16 Bit D/A Channels TXMC639-11R: 8 Single-Ended 16 Bit D/A Channels Output range configurable per D/A channel. Maximum single-ended Output Voltage – Vout: ±10 V Maximum Output Drive Current for each Output: 10 mA Maximum Capacitive Load for each Output: 1000 pF Typical Settling Time for a 10 mA / 1000 pF: < 1 µs | |||||||||
| Digital Front I/O Channels | 32 digital I/O Lines
| |||||||||
| Digital Rear I/O Channels | 64 direct FPGA I/O lines to P14 Rear I/O connector
4 MGT line to P16 Rear I/O connector
| |||||||||
| Front I/O | Front I/O Samtec – ERF8_050_01_L_D_RA_L_TR | |||||||||
| P14 Rear I/O | 64 pin Mezzanine Connector (Molex 71436-2864 or compatible) | |||||||||
| P16 Rear I/O | 114 pin Mezzanine Connector (Samtec – ASP-105885-01) | |||||||||
| Power Requirements 1) | Depends on FPGA design With TXMC639 Board Reference Design / without external load
| |||||||||
| Temperature Range | Operating: – 40 °C to + 85 °C Storage: – 55 °C to + 125 °C | |||||||||
| MTBF 1) | 157 000 h to 161 000 h | |||||||||
| Humidity | 5% – 95% non-condensing | |||||||||
| Weight | 140 g |
1) depends on variant, for further details see User Manual
TXMC639-10R
| 8x Analog In, 4x Analog Out, XC7K160T-2FBG676 Kintex™ 7 FPGA AMD Kintex™ 7 FPGA (XC7K160T-2FBG676), 1GB DDR3, 8x Analog In, 4x Analog Out, 32x digital Front I/O, 64x direct FPGA Rear I/O Lines and 4x MGTs Rear I/O |
TXMC639-11R
| 16x Analog In, 8x Analog Out, XC7K325T-2FBG676 Kintex™ 7 FPGA AMD Kintex™ 7 FPGA (XC7K325T-2FBG676), 1GB DDR3, 16x Analog In, 8x Analog Out, 32x digital Front I/O, 64x direct FPGA Rear I/O Lines and 4x MGTs Rear I/O |
SOFTWARE
Share this product
LinkedIn
